No products in the cart.
Finishing Machinery
Stenter
Hot air stenter
The Stenter or Hot air Stenter Machine is one of the Fabric Finishing Machines, like Relax Dryer, whose heat set capabilities give the fabric the final result of all the processes it went through.
Stenter has detachable nozzle fingers that are easy to clean and sliding filters that remove lint as they come out.
It also comes with an A.C. inverter system that allows the operator to make changes as needed within seconds.
Stenter comes with the following advanced and improved features:
🔶 Higher Production Speeds
✅ Use of elongated oval Nozzle slits for higher air velocity.
✅ The lowest gap between the top and bottom Nozzle faces prevents the drop in enthalpy.
✅ High-energy blower fans displace high volumes of air.
✅ Fabric working width can be customized from 1600mm to 3400mm and cambers from 1 to 12, depending on customer need.
✅ Speed from 40 to 100 meters per minute by A.C. Inverter System.
🔶 Efficiency
✅ Double-jacketed sealed provides the best insulation.
✅ Seasoned cast-iron lubricated rail provides friction-free movement of the chain.
✅ All pipelines are installed inside the machine to cut out conduction losses.
✅ Give 15% More Savings against other stenters.
🔶 Maintenance
✅ Detachable Nozzle fingers for easy cleaning & Online sliding filters for lint removal make it easy to maintain on a daily basis.
✅ Online sliding filters for lint removal.
✅ Easy access inside chambers for observation.
✅ Advanced chamber technology makes it easy to install and reinstall if needed without interfering with the performance.
Working width decides upon the maximum width of fabric & chambers decide upon the maximum per day production required.
As its Fabric Finishing machine, Stenter can finish fabric like Hosiery, Cotton, Polyester, Cotton Hosiery, Polyester Hosiery, Polyester Cotton, Wool, Mink Blanket, Polar, and Many more Knitted as well as woven fabrics.
In Conclusion, this machine is best for Dyeing and Printing Plants.
₹3,000,000.00
Stenter
The Stenter is one of the Fabric Finishing Machines like Relax Dryer whose heat set capabilities to give the fabric the final result of all the processes it went through. Stenter has detachable nozzle fingers that are easy to clean and sliding filters which remove lint as they come out. Stenter also comes with an A.C. inverter system that allows the operator to make changes as needed within seconds.
Stenter comes with the following advance and improved features:
🔶 Higher Production Speeds
✅ Use of elongated oval Nozzle slits for higher air velocity.
✅ The lowest gap between the top and bottom Nozzle faces prevents the drop in enthalpy.
✅ High-energy blower fans displace high volumes of air.
✅ Fabric working width can be customised from 1600mm to 3400mm and cambers from 1 to 12 depending on customer need.
✅ Speed From 40 to 100 meters per minute by A.C. Inverter System.
🔶 Efficiency
✅ Double jacketed sealed provides the best insulation.
✅ Seasoned cast iron lubricated rail provides friction-free movement of the chain.
✅ All pipelines are installed inside the machine to cut out conduction losses.
✅ Give 15% More Saving against other stenter.
🔶 Maintenance
✅ Detachable Nozzle fingers for easy cleaning & Online sliding filters for lint removal make it easy to maintain on daily bases.
✅ Online sliding filters for lint removal.
✅ Easy access inside chambers for observation.
✅ Advance chamber technology makes it easy to install and reinstall if needed without interfering with the performance.
Working width decides upon the maximum width of fabric & chambers decide upon the maximum per day production requires.
As its Fabric Finishing machine, Stenter can finish fabric like Hosiery, Cotton, Polyester, Cotton Hosiery, Polyester Hosiery, Polyester Cotton, Wool, Mink Blanket, Polar and Many more Knitted as well as woven fabrics.
In Conclusion, this machine is best for Dyeing and Printing Plants.
1. Select Product
Choose the required specification & submit the details.
2. Get Offer
Get a Detailed Offer.
3. Pay The Advance
Pay the advance amount as per agreed terms.
4. Product Under Construction
Product goes under Construction according agreed time.
5. Pay The Rest Amount
Pay the balance amount as your machine get ready to dispatch.
6. Shipment Initiated
Shipment option available through Manufacturer.
7. Installation
Finally, the product will be installed at your plant.
Stenter | Fabric Finishing Machine | Book 1 to 12 Chambers | Accurate
Hot air Stenter Machine is one of the Fabric Finishing Machines, like Relax Dryer, which heat set capabilities give the fabric the final result.
Product SKU: F/S-1
Product Brand: Indian
Product Currency: INR
Product Price: 3000000
Price Valid Until: 2027-09-30
Product In-Stock: PreOrder
Editor's Rating:
5
5
| Fabric | Hosiery, Cotton, Polyester, Cotton Hosiery, Polyester Hosiery, Polyester Cotton, Wool, Mink Blanket, Polar |
|---|---|
| Fabric Width | 1600mm, 1800mm, 2400mm, 2600mm, 2800mm, 3000mm, 3200mm, 3400mm |
| Chambers | 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12 |
Stenter | Fabric Finishing Machine | Book 1 to 12 Chambers | Accurate
Hot air Stenter Machine is one of the Fabric Finishing Machines, like Relax Dryer, which heat set capabilities give the fabric the final result.
Product SKU: F/S-1
Product Brand: Indian
Product Currency: INR
Product Price: 3000000
Price Valid Until: 2027-09-30
Product In-Stock: PreOrder
Editor's Rating:
5
5
Youtube
Coming Soon
Stenter | Fabric Finishing Machine | Book 1 to 12 Chambers | Accurate
Hot air Stenter Machine is one of the Fabric Finishing Machines, like Relax Dryer, which heat set capabilities give the fabric the final result.
Product SKU: F/S-1
Product Brand: Indian
Product Currency: INR
Product Price: 3000000
Price Valid Until: 2027-09-30
Product In-Stock: PreOrder
Editor's Rating:
5
5
Based on 0 reviews
Be the first to review “Stenter”
- Dyeing Machinery
Semi Automatic Jigger Machine
Semi Automatic Dyeing Jigger
Roll Center 31″ (790 mm) – 36″ (915mm)
Capacity 350-500 Kg. (250 gsm)
Batch Dia 900-1100 mm
Available Width : 48″ To 150″ Roller WidthSemi Automatic Jumbo Jigger Machine
Roll Center 31″ (790 mm) – 36″ (915mm)
Capacity 350-500 Kg. (250 gsm)
Batch Dia 900-1100 mm
Available Width : 48″ To 150″ Roller Width[spbsm-follow-buttons]
SKU: n/a - Accessories
Bag Filter
Bag Filter
A Bag Filter, also known as a dust collector, is a most required Accessory for boiler houses in textile plants and mills. The primary object of the Bag filter is to clean dirty air or gas by trapping dust and particles before the air goes from the chimneys of the Plants and Mills.
The Bag filter consists of multiple woven bags. The bag filter typically holds between 56 and 320 bags, depending on the capacity of the Boiler or Thermopac. These filters effectively capture dust and particles, helping the equipment work efficiently. Their design ensures they fit well with the system while allowing necessary airflow. It has the following features that make it an essential part of Boiler Houses in Textile Plants:
- Firstly, it cleans dirty air and gases by catching them in bags before the air enters the environment.
- Secondly, it helps to contain dirt and pollutants from the air, making the workplace safer for workers and the environment.
- Thirdly, in industries like textiles, even tiny dust particles can affect the quality of the product. Bag filters help maintain a clean environment.
- Fourthly, it is a highly customizable product that can carry between 56 and 320 bags, depending on the capacity of the Boiler or Thermopac.
- Fifth and most importantly, Governments have strict rules on air pollution. Bag filters help companies follow these rules to avoid fines or shutdowns.
Conclusion:
Bag filters are essential for modern industry. They clean the air by removing dust and particles, protecting people and machines. They work efficiently, are built to last, and can be used in different industries, including textile, cement, and food production.
Using bag filters helps industries maintain clean air, comply with environmental laws, and create a safer workplace. They are a wise investment for any company seeking to enhance safety and productivity.
🔸 Technical Specification
✅ Can be customized from 56 to 320 bags.
✅ Attach with Boiler or Thermopac (Thermic Fluid Heater)
✅ From capacity 2 tons to 10 tons (Boiler) & from capacity 500U to 5000U (Thermic Fluid Heater)
SKU: A/BF-1 - Washing Machinery
Open Width Washing Range
Open width Washing Range
Open width Washing Range is for the fabric washing machine for woven fabrics. The Open width Washing Range machine has the following features.
- Firstly, The system consists of a specially shaped impeller in the drum in which water jets uniformly smashes the full fabric width very high washing performance on the upper and backside of the fabric.
- In other words, Open width Washing Range removes unfixed dyestuff, gum, and other chemicals from the fabric.
- Secondly, Washing with tanks can carry out pre-washing, rinsing, and chemical treatment.
- Therefore, Open width Washing Range improves fabric quality.
- An effective squeezer between the washing unit gives maximum liquor separation from one bath to another.
- Thirdly, Each washing compartment with its force-spray system, re-circulation pump, filtering device, overflow, drain, and heating arrangement.
- Fourthly, the Open width Washing Range’s working width is to be made from 1500mm to 3500mm depending on the client’s need.
- Fifthly, ranging from 70 gsm/meter square up to 700 gsm/meter square of woven fabric can be processed on this machine.
- Sixth and most Important is Perfect synchronizing of linear speed hence tension-less and creaseless transport of fabric all along the process.
🔶 ADVANTAGES :
✅ Excellent Washing efficiency.
✅ Extremely sturdy construction.
✅ Quiet running.
✅ Low energy consumption.
✅ Ease of operation.
✅ Optional knife spray between each strand of fabric with supply from a separate pump.
✅ Circulation and counter flow arrangement to save water.
✅ Low maintenance.
✅ Quick and simple installation.
✅ Tight closing glass windows on the sides to provide easy access.
✅ Direct steam heating by perforated S S Pipes.
✅ S S bottom rolls running in self-aligning bush bearing.
SKU: n/a - Processing Machinery
Polymeriser
Polymeriser
Polymeriser is to use for fixing printed garments. Polymeriser is an Important part of Processing machinery cause it secures the colour before the washing and finishing. There are the following features in it.
- Firstly, Polymeriser assures perfect fixation of dyes even at higher temperatures. In other words, the Dyes can be permanent before starting the washing and finishing process of the cloth.
- Secondly, It is most suitable for curing Phthalein dye, Pigments, and resin set.
- Thirdly, Pre-dryer removes gaseous fumes from printed fabrics – an exclusive speciality of this Machine. The Machine operates efficiently in the temperature range from 30ºC Temperature to 180ºC and ensures automatic regulation of temperatures within the chamber.
- Fourthly, the width can be made from 1600mm to 3200mm as per the client’s need.
- Fifthly, Garment weighted from 70 to 700 gsm/per meter square can be processed.
- The sixth and most Importantly speed can be achieved up to 40 meters per minute while performing the process.
In conclusion, Polymeriser is best suitable for the garment industry or dyeing & printing plants.
🔸 ADVANTAGES :
➡ Supply with hot air jets, recirculating fans and steam or thermic oil heating for best curing result.
➡ Separate blowers for top and bottom air nozzles.
➡ Its uniformity in temperature, width-wise, length and diagonally.
➡ No dropping by condensation.
➡ Variable speed up to 40 meters per minute by A.C. Inverter System.
➡ It is available in 60 to 150 meters of cloth content curing zone.SKU: P001 - Dyeing Machinery
Regular Jet
Regular Jet dyeing
This machine is best for polyester fabric dyeing cause it runs on a high pressure of high-temperature water. Regular Jet dyeing is economical because the low liquor ratio reduces everything.
The fabric inside this polyester dyeing machine moves solely due to the force of water.
It is user-friendly because, If we compare it with a Long tube dyeing machine. Four valves are necessary to control the fabric’s motion. Here in Regular Jet dyeing, there is only one valve.
Absent of reel, reduce connecting electric power, maintenance of two mechanical seals and breakdown time if Jet pressure and reel speed are not synchronized.
Nearly 4000 without fabric drive reel devices are saving energy and lowering pollution in 20 countries.
🔸 Technical Specification
✅ Capacity: 25 to 400Kg.(Single Tube)
✅Ultra Low Liquor Ratio – 1:1 (Wet Fabric)
✅ Dye – 30 To 450 Grms./Mtr. Sq. Fabrics (Woven & Knitted Fabrics)
✅ High Temp. – Up to 140 ° C.
✅ Fabric Speed – 300 Mtr./Min.
✅ Vessel: SS 316 LBest Polyester dyeing machine with a low liquor ratio in a Jet dyeing form.
SKU: D/JD-1 - Boiler, Heating Solution
Gas Boiler
GAS Boiler
The Gas Boiler is a packaged three-pass smoke tube with a total wet back boiler. Gas Boiler comes in two three series for burning light oils & gas and heavy oils.
The Gas Boiler also can be customized to a complete skid mount unit on customer demand.
When fitted with a particular burner, these boilers are ideal for burning waste gases like biogas from the decomposition of organic matter in distilleries.
🔸 PRODUCTS FEATURES:
✅ Three-pass smoke tube with complete wet back boiler.
⭕ Multi-fuel option – light oils/heavy oils/gases
✅ High efficiency of about 88% to 95%
✅ High dryness fraction steam increases usable heat.
✅ Gas Boiler Comes with mono-block/ dual block/steam atomized burner with world-renowned Technology from (ITALY)
⭕ An additional option of oil pre-heater confirming EN safety standards
✅Corrugated furnaces for boilers above 6 TPH capacity.
⭕ Optional PLC-based control panels that would be linked to SCADA or DCS systems.🔸 Operating Range:
➡ Capacities In the range of 1.0 TPH to 15 TPH
➡ Pressure: In the range of 10.54 to 17.54 Kg/cm2 (g)
➡ Firing fuels: LDO, FO, LSHS & Natural Gas
➡ Efficiency: Overall efficiency of 88 % (+/-2%) on NCVSKU: H/GB-1
Related products
- Finishing Machinery
Compressive Shrinking Range
The Sole purpose of the Controlled Compressive Shrinking Range or ZEROZERO is to ensure that the garment made from such fabric does not shrink after the wash hence perfect dimensional stability.
As per standard, + / -1 % residual shrinkage is acceptable. Controlled Compressive Shrinking Range or ZEROZERO are available up to 3200mm working width fabric to assure total shrinkage protection to woven fabrics. It can be 100% cotton, cotton/polyester, cotton/viscose or tough and heaviest fabric like denim. Compressive Shrinking Range or ZEROZERO developed in a way that can shrinkage up to 12% in a single passage.
The most capable of shrinking medium, lightweight fabric to the heaviest denim, cotton blended suiting & shirting by watering cotton, terylene, hemp and its blends to shrink the cloth to meet the requirements of shrinkage, stabilization and improve the hand touch.
A controlled Compressive Shrinking Range is usually the last process in the sequence of fabric finishing. The woven fabric processed in the machine gets fully shrunk.
Before compressive shrinking, it is advisable to establish the width at which the cloth should get shrunk in length to meet the requirement of the garment makers. It is the best Fabric Finishing machinery.
🔸 Technical Specification
✅ A.C. frequency conversion transmission, designed speed: 10-80m/minute.
✅ Shrinkage 0 – 12 % depending upon fabric quality.
✅ Minimum and controlled tension.
⭕ Imported Rubber Blanket and Polyester Felt will be provided optionally.
✅ A Jacketed drum in 1500mm, 2000mm and 2500mm diameters.
✅ Stainless Steel damping & conditioning unit supplied as standard Parts.SKU: n/a - Finishing Machinery
Loop Ager
Loop Ager
Loop Ager can be offered in five variants as mentioned below:
- DIGIFIX Specially designed Machine for Digital Printing
- ATMOFIX suitable for Low-Temperature Application
- EVOMAX suitable for High-Temperature Applications
- RAPIFIX suitable for Hot Air and Pigment Application
- UNIFIX is appropriate for both Low Temperature & High-Temperature applications
Loop agers are simple to use on almost any fabric that has been printed using different printing recipes. The high versatility of steam agers, together with high qualitative standards, allows their utilization in all continuous production lines for the colour fixation processes.
❇ ATMOFIX Loop Agers, the quantity of steam is injected more at the entry of the fabric as on the first few loops.
Moisture condenses on the cloth with the Exothermic reaction for colour fixation. UREA dissociation takes place in the initial few seconds By when the water vapour is distributed/injected into the chamber accordingly.
❇ EVOMAX Loop Agers are suitable for high-temperature streaming applications.
The Steam consumption is comparatively less because of the compact design of chambers manufactured by SS 316 with larger Thermos Oil Radiators/ Heaters/Gas Burners installed to heat the section faster when processing with High-Temperature steaming applications or Hot Air applications.
❇ RAPIFIX Loop Agers are robust and suitable for any working atmosphere. Curing Machines constructed of Mild Steel on the inside with an outer body made of Insulating Panels are fit for this process because the required temperature is above 130°C & the machine operates in moisture-free conditions on the inside.
Essentially, the Dyes are set to the cloth during the Curing Process by polymerization in hot air at 150°C to 160°C.
Loop Agers fabric moves in tensionless conditions. So, there are no chances for lengthwise stretching and no rubbing effect on the cloth.
In any ageing machine, the transportation of the fabric in the hanging loop form makes the fabric move in a tensionless motion.Oil radiators & centrifugal blowers are provided which help circulation Of the surrounding air through the filters & blows it into the machine from the bottom part of the machine.
An exhaust fan removes the Hydrocarbons & Condensed Oil.
🔸 Key features of the Loop Ager Machine:
1. Compact steaming chamber design to reduce steam consumption.
2. Even the distribution of steam in the chamber, steam injected from the top & lighter than the air will force to remove air and exhaust from the bottom will be occupied in the process chamber fully make it leaving no chance of air inside the steaming compartment.
3. Optimum steam conditioning and humidification with parallel flow inside the steamer.
4. Conveyor rollers treated with shot blasting that rotates on their axis to prevent marking off from the rod itself.
5. A loop rod roller mechanism is used to create loops.
6. The steaming chamber is a closed type made of stainless steel.
7. For low-temperature steaming of the chamber roof and entry, the delivery slit is heated by steam coils preventing condensation and dripping on the fabric.
8. DIGIFIX, ATMOFIX and UNIFIX Loop Agers are equipped with a special device steam saturator that conditions the steam. It passes through the water before being injected into the steaming chamber.
These characteristics of steam pre-conditioning help prevent and control the exothermic reaction of the fabric with the printing paste. Making the machine unique & use The temperature control system/moisturising system for the said machines is the basis of the remarkable success achieved in the textile industries for Low-Temperature Applications.
9. The EVOMAX and UNIFIX Loop Agers are fitted with an effective re-circulation system and heat exchanger using either thermic fluid or direct gas fire system for high-temperature steaming, ensuring uniform temperature throughout the chamber.
10. A unique system to allow air to re-circulate in our RAPIFIX Loop Ager instead of steam permits Polymerization treatment with stifling air up to 160 ͦC.
11. Two enormous size access windows are provided on the front side, two small inspection windows on the back side and one small size window on the Drive arrangement platform.
12. Steam exhaust fan driven by variable speed AC motor, all fabric movements are pushed by variable speed AC motor.
13. Automatic control PLC system for programming and monitoring steam quantity, steam pressure, processing time & temperature is optional with our “PRO” version of all the variants of Loop Agers and Curing machines.
14. “LITE” versions of machines are also available for all variants of Agers and Curing machines for Manual operations and are also equipped with Modbus protocol and a 7” HMI for comfortable functions.
SKU: n/a - Finishing Machinery
Denim Finishing Range
Denim Finishing Range
The Denim Finishing Range Exclusive purpose is to ensure that the garment made from such fabric does not shrink after the wash hence perfect dimensional stability.
As per standard, + / -1 % residual shrinkage is acceptable. Denim Finishing Range is available for up to 3600mm working width fabric to assure total shrinkage protection to Denim fabrics.
Denim Finishing Range was developed in a way that can shrinkage up to 14% in a single passage.
Denim Finishing Range is usually the last process in the sequence of fabric finishing. The Denim fabric processed in Denim Finishing Range gets fully shrunk.
Before Denim Finishing Range, it is advisable to establish the width at which the cloth should get shrunk in length to meet the requirement of the garment makers. It is the best Fabric Finishing machinery.
🔸 Key Features:
✅ Ensuring Required Shrinkage of 14 Ounce Denim in Single RUN At a Speed of 40 to 50 Mtrs / Min.
✅ Matching all parameters of Shrinkage, Feel, Warp & Weft Tension.
✅ Complete Machine with P.L.C. Controlled Inverter Drive.
✅ Large Touch Screen, Showing Shrinkage, Speed and Other Data, Minimum Usage, of Steam & Power.
✅ User-friendly machine with the shortest Payback time.
✅ Can finish lycra fabrics in a single run with required weft and warp shrinkage at the speed of 40 mt / min.
✅ Specially designed heavy warp pull to control the width of the fabric and warp stretch control by P L C.
✅ Motorized antiskew device to control the skew setting of fabric twill by forwarding and reversing the movement of motors.
✅ Specially developed a shrinking unit to achieve shrinkage up to 14 % depending upon the quality of the fabric with residual shrinkage of 1 %.
✅ 2500mm dia Mirror polished Jacketed main palmer cylinder with rotary joints.
✅ The number of 2 cooling cylinders is provided at the exit of the palmer unit to cool down the fabrics.
⭕ Singing unit at the feeding side. (Optional)
⭕ Brushing unit at feeding side. (Optional)
⭕ Temperature controlling of shrinkage and palmer unit by PLC. (Optional)
⭕ Big Batching device with ‘J’ scray at plating side. (Optional)
SKU: F/DFR-1 - Finishing Machinery
Relax dryer
The Relax Dryer is the finishing machine to dry hosiery fabric after the fabric has been washed or processed. This Relax Dryer has the following features in it.
- Firstly, The air movement produces undulations in the cloth & at the same time, it expands the knitted fabric causing dimensional shrinkage and selvedge opening.
- In other words, Relax Dryer expands the fabric width while drying it.
- Secondly, Relax Dryer rolls ladder-proof fabrics based on well-known the principle of air impact drying system.
- Thirdly, the cloth moved through the drying chamber on a conveyor belt that overfed to increase length shrinkage.
- Fourthly, The operating width of the Relax Dryer can range from 1600mm to 4200mm. Depending on the specific needs of the client.
- Fifthly, Relax Dryer can process fabric ranging from 70 to 700 gsm/meter square of hosiery.
- Sixth and most Important, velocity can be achieved up to 60 meters per minute while performing the process.
In conclusion, Relax Dryer is best suitable for Dyeing & Printing units.
🔸 Technical Specification
✅The number of chambers: 2 to 8.
✅Conveyor belt width: 1600mm to 4200mm.
✅ Heating system alternatives: Natural Gas, LPG, Steam or Thermic Oil.
✅ Mechanical belt speed: Step less than 0 to 60m/min.
✅ Maximum working temperature: 220 °C.
✅ Blowers: Special design, highly efficient, diagonal location, two blowers in each chamber.
✅ Fabric feeding: Step-less by multiple points.
✅ Conveyor belt direction control: Electro-pneumatic from both sides.SKU: RD001
There are no reviews yet.